Talk is Jeep!

AKA Bar and Grill - General Discussion of any topics, does not need to be related to metal trading.
User avatar
Rodebaugh
Jester
Posts: 4050
Joined: Wed Oct 05, 2011
Location: Almost Heaven

Re: Talk is Jeep!

Postby Rodebaugh » Mon Sep 04, 2017

natsb88 wrote:
Rodebaugh wrote:It is mounted between my gate and spare. :thumbdown:


MaxGravy wrote:The CB whip belongs on the FRONT bumper. You're so unhip.

You're both wrong :P

A CB antenna actually belongs in the center of the roof (assuming you have a metallic roof).

Standard CB antennas (like a Firestik) require a metallic ground plane to reflect the transmission energy up and away. The larger and flatter, the better.

Bumper mounts are problematic in two ways. One is the unbalanced (and much smaller) ground plane that comes with this location, and the other is interference from reflections of the transmission energy off of vertical surfaces around the top two thirds or so of the antenna (like the back of a Jeep). This feeds energy back into the antenna, which is bad. Both of these problems lead to high SWR and can damage your radio when transmitting.

All that said, bumper mounts work for short range communication, but you need to throw an SWR meter on there and tune it in. CB antennas always need to be tuned, but especially when mounted in compromising positions like bumpers. The front bumper is less bad than the back bumper since the antenna at least isn't right up against vertical surfaces like it is on the back.

Don't fry your rig :shock:

http://firestik.com/Tech_Docs/Bumper-mnts.htm


That's what fuses are for. :thumbup:

I will downgrade my 4 footer to a 2 footer. Placed very similar to the picture below. I need about a half mile tops. Folks get about 2 miles out of a rig like this:

tenna.png
tenna.png (464.3 KiB) Viewed 1419 times

User avatar
MaxGravy
Site Admin
Posts: 15095
Joined: Sat Jul 18, 2009
Location: Texas!

Re: Talk is Jeep!

Postby MaxGravy » Mon Sep 04, 2017

Can we call you stubby?
Image Image Image
Don't grow up - it's a trap!

User avatar
Rodebaugh
Jester
Posts: 4050
Joined: Wed Oct 05, 2011
Location: Almost Heaven

Re: Talk is Jeep!

Postby Rodebaugh » Mon Sep 04, 2017

MaxGravy wrote:Can we call you stubby?


:lol:

That's better than mall crawl or grocery getter. :thumbup:

Image

User avatar
Rodebaugh
Jester
Posts: 4050
Joined: Wed Oct 05, 2011
Location: Almost Heaven

Re: Talk is Jeep!

Postby Rodebaugh » Tue Sep 12, 2017

Recommendations for an SWR meter?

Little cheapie like this work?
http://www.ebay.com/itm/ASTATIC-PDC1-SW ... Sw9UlZkva~

MaryB
Posts: 595
Joined: Thu May 10, 2012

Re: Talk is Jeep!

Postby MaryB » Thu Sep 14, 2017

Those are highly inaccurate this is the minimum I would get https://www.gigaparts.com/mfj-813.html using an antenna analyzer is better https://www.dxengineering.com/search/pa ... =Ascending and you could recoup the costs by tuning other jeepers antennas for $20 each

User avatar
Rodebaugh
Jester
Posts: 4050
Joined: Wed Oct 05, 2011
Location: Almost Heaven

Re: Talk is Jeep!

Postby Rodebaugh » Tue Oct 10, 2017

Everything (big) is done for now. Jeep took it's last major step from Stock to ROCK.
Poison Spyder Fenders Flairs and Inners. Powdercoated with flats painted to match OEM white.

8-)

IMG_1553[1].jpg
IMG_1553[1].jpg (158.9 KiB) Viewed 1164 times


IMG_1588[1].jpg
IMG_1588[1].jpg (183.89 KiB) Viewed 1164 times

User avatar
H2SO4
Gold Jeeper
Posts: 2707
Joined: Thu Jul 15, 2010
Location: St. Elmo, Colorado

Re: Talk is Jeep!

Postby H2SO4 » Tue Oct 10, 2017

looks good, doc!
Always looking for BS Bars- any serial numbers. Buy/Trade
Image

User avatar
Rodebaugh
Jester
Posts: 4050
Joined: Wed Oct 05, 2011
Location: Almost Heaven

Re: Talk is Jeep!

Postby Rodebaugh » Fri Oct 27, 2017

Video of the Jeep doing a little work. Sorry Randy....it's a facebook link. :sick:

https://www.facebook.com/25824208/video ... 611796019/

User avatar
Rodebaugh
Jester
Posts: 4050
Joined: Wed Oct 05, 2011
Location: Almost Heaven

Re: Talk is Jeep!

Postby Rodebaugh » Fri Oct 27, 2017

Image

Image

Image

User avatar
natsb88
Turtle Supporter
Posts: 5178
Joined: Sun Sep 20, 2009
Location: The Copper Cave
Contact:

Re: Talk is Jeep!

Postby natsb88 » Fri Oct 27, 2017

Rodebaugh wrote:Video of the Jeep doing a little work. Sorry Randy....it's a facebook link. :sick:

https://www.facebook.com/25824208/video ... 611796019/


:(

jeep.JPG
jeep.JPG (23.04 KiB) Viewed 1087 times

User avatar
Rodebaugh
Jester
Posts: 4050
Joined: Wed Oct 05, 2011
Location: Almost Heaven

Re: Talk is Jeep!

Postby Rodebaugh » Sat Oct 28, 2017

Ill get some videos posted later after company leaves. Until then a little flex and wave.

Image

User avatar
Rodebaugh
Jester
Posts: 4050
Joined: Wed Oct 05, 2011
Location: Almost Heaven

Re: Talk is Jeep!

Postby Rodebaugh » Mon Nov 06, 2017

So here is what my front pinch seam looked like after the trim from my poison spyder install. Note that the optional aluminum spyder inner fenders are there I just had them rhino lined. There is no way I could leave such a gaping hole right behind my tires. With the trails I run I would have that packed tight with about 15lbs of mud, rock, and leaves. Water is not an issue as these panels have a built in drain. I just don't want my jeep to have any areas that I can plant tomatoes and expect a harvest.

IMG_1613.jpg
IMG_1613.jpg (336.68 KiB) Viewed 1018 times


Not impressed with the ill fitting aftermarket options I decided to do a simple custom fab myself using a cardboard template and sheet aluminum sourced from the local Tractor Supply. After 3 or 4 times each side fitting and trimming I was pleased with the coverage.

IMG_1612.jpg
IMG_1612.jpg (437.39 KiB) Viewed 1018 times


A couple coats of Rustoleum aluminum etch was sprayed as a base followed by 3 coats of black rattlecan chip gaurd.

IMG_1611.jpg
IMG_1611.jpg (172.23 KiB) Viewed 1018 times

User avatar
Rodebaugh
Jester
Posts: 4050
Joined: Wed Oct 05, 2011
Location: Almost Heaven

Re: Talk is Jeep!

Postby Rodebaugh » Mon Nov 06, 2017

Tomato planter gaping hole.

IMG_1614.jpg
IMG_1614.jpg (289.93 KiB) Viewed 1017 times


Finished clean seamless seam

IMG_1616.jpg
IMG_1616.jpg (291.02 KiB) Viewed 1017 times


IMG_1618.jpg
IMG_1618.jpg (289.34 KiB) Viewed 1017 times



Also, I now have a rear passenger bent axle shaft.
So guess what my next project is. :lol:

User avatar
Rik Bitter
Gold Jester
Posts: 2100
Joined: Mon Jul 25, 2016
Location: PA

Re: Talk is Jeep!

Postby Rik Bitter » Mon Nov 06, 2017

1) Buy nice stuff.
2) Break nice stuff.
3) Repeat.

Jeep people are special.
*** LOOKING FOR YPS #18s. Please contact me if you have any for sale.***


ImageImage

User avatar
Rodebaugh
Jester
Posts: 4050
Joined: Wed Oct 05, 2011
Location: Almost Heaven

Re: Talk is Jeep!

Postby Rodebaugh » Mon Dec 11, 2017

Harvested a nice fat Doe with my muzzleloader this past weekend. Found a new use for my stinger.

IMG_1735[1].jpg
IMG_1735[1].jpg (243.23 KiB) Viewed 751 times

User avatar
H2SO4
Gold Jeeper
Posts: 2707
Joined: Thu Jul 15, 2010
Location: St. Elmo, Colorado

Re: Talk is Jeep!

Postby H2SO4 » Mon Dec 11, 2017

thats awesome! was the muzzle loader the new one from Silencer Co?
Always looking for BS Bars- any serial numbers. Buy/Trade
Image

User avatar
Rodebaugh
Jester
Posts: 4050
Joined: Wed Oct 05, 2011
Location: Almost Heaven

Re: Talk is Jeep!

Postby Rodebaugh » Mon Dec 11, 2017

H2SO4 wrote:thats awesome! was the muzzle loader the new one from Silencer Co?


No, but I did check them out at my local sporting good shop. Pretty neat firearm for sure.

I shoot a TC Triumph Bone Collector w/ Vortex copperhead 4x12x44 Scope. Barns 240 grain TEZ full copper Sabots and (2) 50 grain Hodgdon triple seven powder. I plan to play around a bit with my loads this summer.

Side by sides and ATV's are for folks that don't have a wrangler.
IMG_1725[1].jpg
IMG_1725[1].jpg (367.55 KiB) Viewed 727 times

User avatar
Rodebaugh
Jester
Posts: 4050
Joined: Wed Oct 05, 2011
Location: Almost Heaven

Re: Talk is Jeep!

Postby Rodebaugh » Mon Apr 16, 2018

Finding that perfect 2 wheel on the ground spot. :angel:


User avatar
Rodebaugh
Jester
Posts: 4050
Joined: Wed Oct 05, 2011
Location: Almost Heaven

Re: Talk is Jeep!

Postby Rodebaugh » Mon Jun 11, 2018

Potts Mountain Jeep run last weekend. Good stuff. Winched my buddy once and stacked a couple times.

IMG_2224[1].jpg
IMG_2224[1].jpg (680.46 KiB) Viewed 114 times

User avatar
Rik Bitter
Gold Jester
Posts: 2100
Joined: Mon Jul 25, 2016
Location: PA

Re: Talk is Jeep!

Postby Rik Bitter » Mon Jun 11, 2018

Rodebaugh wrote:Winched my buddy once and stacked a couple times.


I thought the upright God-fearing citizens of West Virginia had laws against that sort of thing.
*** LOOKING FOR YPS #18s. Please contact me if you have any for sale.***


ImageImage


Return to “Burgers and Beers”

Who is online

Users browsing this forum: No registered users and 4 guests